Search found 18 matches

by Hamman
Tue Sep 19, 2017 10:15 am
Forum: Technical Discussion
Topic: Antigravity Battery Question
Replies: 5
Views: 76

Re: Antigravity Battery Question

Contact this guy. I built a CX500 a few months ago and did an antigravity 8 cell battery. It HAD to have the rectifier upgraded. It also had an older shindengen one but it would over charge a Li battery. Really easy to wire in but does cost a good amount of money. I'd contact him and see if his are ...
by Hamman
Mon Sep 11, 2017 2:11 pm
Forum: Technical Discussion
Topic: 82 SC CV carb jetting
Replies: 1
Views: 67

Re: 82 SC CV carb jetting

UPDATE: I went with the stock 35 pilots, 116 dynojets and 3 washers (1.5mm) total under the needle. Idle/mid is now killer. Higher rpm's are lagging. The only kicker is my fuel/air screws are pretty much maxed out which means either up the main (I have a 122 dynojet) or adding washers to give more g...
by Hamman
Sun Sep 10, 2017 4:33 pm
Forum: Technical Discussion
Topic: 82 SC CV carb jetting
Replies: 1
Views: 67

82 SC CV carb jetting

Do you all think a 45 pilot is too rich for pods and 4-2 exhaust? I am right at about sea level. My other option is the stock 35 pilot that came when I picked up the bike. Figuring out mains too. I have left over Dynojet 116's, stock 118's and I think some 115's. On JetsRus they have a conversion ch...
by Hamman
Mon Aug 28, 2017 12:29 am
Forum: Technical Discussion
Topic: Blade Fuse Upgrade
Replies: 6
Views: 195

Re: Blade Fuse Upgrade

All good, haven't had time to get to it yet. Will be this week. I have 4 in-line mini ATC fuses that I plan on running. It is not an actual junction box or anything, just stand alone fuses in their holders. I will be branching 4 smaller lines off the thicker power wire running to each fuse with prop...
by Hamman
Sat Aug 26, 2017 1:58 pm
Forum: Technical Discussion
Topic: Shifter Peg Oil Seal
Replies: 9
Views: 3304

Re: Shifter Peg Oil Seal

Just did mine yesterday. Took me a bit to get the old seal out but it popped out eventually! Lubed up the new seal and in it went!
by Hamman
Sat Aug 26, 2017 10:35 am
Forum: Technical Discussion
Topic: Blade Fuse Upgrade
Replies: 6
Views: 195

Re: Blade Fuse Upgrade

Ok makes sense..I guess that would not be a ground as that would not make sense for the circuit! So did you just branch off 4 small wires and connectors off that main HOT wire to the corresponding fuses unless I can try and find a 4-1 wire connector..Thanks guys for any/all info!
by Hamman
Fri Aug 25, 2017 11:08 am
Forum: Technical Discussion
Topic: Blade Fuse Upgrade
Replies: 6
Views: 195

Blade Fuse Upgrade

Hey all, Ive been searching for a bit but haven't found a definitive answer. I am replacing all the glass type fuses to blade style. I see that all the fuses have their own power in, but then they all connect to one "black" wire which I assume is ground. I have inline ATC style fuses that ...
by Hamman
Fri Aug 25, 2017 11:06 am
Forum: Technical Discussion
Topic: 1982 Nighthawk CB650sc Starting troubles
Replies: 6
Views: 200

Re: 1982 Nighthawk CB650sc Starting troubles

I'd pop off the tap and take it apart if possible and blow some compressed air through it. If anything, switch over to the manual style.
by Hamman
Tue Aug 22, 2017 5:13 pm
Forum: Technical Discussion
Topic: Rocker Cover Install
Replies: 2
Views: 125

Re: Rocker Cover Install

Sweet, I had it on and the motor spun over freely a few times, no binding, etc... but still freaked me out so I undid all of it..probably was more than fine though haha. :wink:
by Hamman
Tue Aug 22, 2017 10:46 am
Forum: Technical Discussion
Topic: Rocker Cover Install
Replies: 2
Views: 125

Rocker Cover Install

Hey guys, just wanted to confirm before I go bending valves....Are you loosening all of the rocker arms on the head before installing it onto the cylinder? I tried to install it last night but stopped immediately once I realized it shouldn't be this difficult to install. There was a lot of tension o...
by Hamman
Mon Aug 14, 2017 10:42 am
Forum: Technical Discussion
Topic: Float bowl Needle Valves***FIXED***
Replies: 7
Views: 254

Re: Float bowl Needle Valves***FIXED***

Yeah, thanks again guys for your time.
by Hamman
Sun Aug 13, 2017 12:26 pm
Forum: Technical Discussion
Topic: Float bowl Needle Valves***FIXED***
Replies: 7
Views: 254

Re: Float bowl Needle Valves

Fixed....I think I earned dumb ass of the week!!!! Haha. FML. I had the floats upside down and the tang on the float was pushing down on the valve :| Yeah....All good now. Bike started immediately and runs great..Thanks for your time :D
by Hamman
Sun Aug 13, 2017 10:53 am
Forum: Technical Discussion
Topic: Float bowl Needle Valves***FIXED***
Replies: 7
Views: 254

Re: Float bowl Needle Valves

Hey George, no laughs here! Just want to get this damn thing figured out. So yes, I have tried it with both on and off the bike. I used the cotton swab on a very very low speed. Suppose it could have still built up a charge? I have tried installing the valves in the holders without the floats as wel...
by Hamman
Sat Aug 12, 2017 10:45 pm
Forum: Technical Discussion
Topic: Float bowl Needle Valves***FIXED***
Replies: 7
Views: 254

Float bowl Needle Valves***FIXED***

Finally got my carbs all cleaned and put back together. Took all 4 carbs apart and replaced every o-ring etc... everything is awesome! BUT, I am not getting gas to the float bowls. I think I found the problem...sticking needle valves. I can pull the bowls, floats, valves and run gas into the fuel in...
by Hamman
Tue Aug 01, 2017 9:33 am
Forum: Bikes
Topic: 1982 CB650SC Parts For Sale
Replies: 4
Views: 363

Re: 1982 CB650SC Parts For Sale

Rear wheel. Tire is newer and in good usable condition as well
Looking for $75 for rear wheel and tire, plus w/e shipping is to you
Looking for $100 for seat assembly plus shipping

Thanks!
image7.jpeg
image7.jpeg (740.11 KiB) Viewed 291 times
image6.jpeg
image6.jpeg (924.33 KiB) Viewed 291 times
image5.jpeg
image5.jpeg (954.38 KiB) Viewed 291 times

Go to advanced search